JADWAL TRAINING / PELATIHAN / DIKLAT / SEMINAR / WORKSHOP / BIMTEK ”CONTROL VALVE : Operation, Maintenance & Troubleshooting – TERBARU  BULAN  JANUARI – FEBRUARI – MARET – APRIL – MEI – JUNI – JULI – AGUSTUS – SEPTEMBER – OKTOBER – NOVEMBER – DESEMBER 2017 – 2018 – 2019 – 2020 – 2021 – 2022 – ISI FORM REQUEST (KLIK DISINI) atau Hubungi kami.

DESKRIPSI
To reduce the effect of these load disturbances, sensors and transmitters collect information about the process variable and its relationship to some desired set point. A controller then processes this information and decides what must be done to get the process variable back to where it should be after a load disturbance occurs. When all the measuring, comparing, and calculating are done, some type of final control element must implement the strategy selected by the controller.
The most common final control element in the process control industries is the control valve. The control valve manipulates a flowing fluid, such as gas, steam, water, or chemical compounds, to compensate for the load disturbance and keep the regulated process variable as close as possible to the desired set point.
Many people who talk about control valves or valves are really referring to a control valve assembly. The control valve assembly typically consists of the valve body, the internal trim parts, an actuator to provide the motive power to operate the valve, and a variety of additional valve accessories, which can include positioners, transducers, supply pressure regulators, manual operators, snubbers, or limit switches.
Whether it is called a valve, control valve or a control valve assembly is not as important as recognizing that the control valve is a critical part of the control loop. It is not accurate to say that the control valve is the most important part of the loop. It is useful to think of a control loop as an instrumentation chain. Like any other chain, the whole chain is only as good as its weakest link. It is important to ensure that the control valve is not the weakest link.
Following are definitions for process control, sliding-stem control valve, rotary-shaft control valve, and other control valve functions and characteristics terminology.

Objective :
1.    To able know to introduction to control valves
2.    To able know to control valve performance
3.    To able know to valve and actuator types
4.    To able know to control valve accessories
5.    To able know to control valve selection
6.    To able know to special control valves
7.    To able know to installation and maintenance

OUTLINE MATERI :
1.    Introduction to Control Valves: What Is A Control Valve?, Process Control Terminology, Sliding-Stem Control Valve Terminology, Rotary-Shaft Control Valve Terminology, Control Valve Functions and Characteristics Terminology.
2.    Control Valve Performance: Dead Band, Actuator-Positioner Design, Valve Response Time, Valve Type And Characterization, Valve Sizing.
3.    Valve and Actuator Types: Control Valves, Control Valve End Connections, Valve Body Bonnets, Control Valve Packing, Characterization of Cage-Guided Valve Bodies, Valve Plug Guiding, Restricted-Capacity Control Valve Trim, Actuators.
4.    Control Valve Accessories: Positioners, Other Control Valve Accessories
5.    Control Valve Selection: Valve Body Material, Designations for the High Nickel alloys, Pressure-Temperature Ratings for Standard Class, Face-to-Face Dimensions, Control Valve Seat Leakage Classifications, Control Valve Flow Characteristics, Valve Sizing, Non-Destructive Test Procedures, Cavitation and Flashing
6.    Special Control Valves: High Capacity Control Valves, Low Flow Control Valves, High-Temperature Control Valves, Cryogenic Service Valves, Customized Characteristics and Noise Abatement Trims, Valves Subject to Sulfide Stress Cracking
7.    Installation and Maintenance: Proper Storage and Protection, Proper Installation Techniques, Control Valve Maintenance, Actuator Diaphragm, Stem Packing, Seat Rings, Bench Set.

PESERTA
Para praktisi tingkat operator, tingkat penyelia atau perencana bidang perawatan mesin pada industri rekayasa.

Permintaan Brosur penawaran Training ( Harga, Waktu dan Tempat) silahkan Menghubungi kami.

Catatan :

  • Pelatihan ini dapat di-customized sesuai kebutuhan perusahaan Anda bila diselenggarakan dalam bentuk In-House Training. Untuk permintaan In-House Trainingdengan jenis topik lainya, silahkan mengirimkan ke alamat email yang tercantum di web kami.

  • Request Training. Jika anda membutuhkan informasi pelatihan yang belum tercantum pada website ini, atau anda ingin memberikan usulan materi yang sesuai dengan tingkat kebutuhan perusahaan anda, silahkan mengirimkan ke alamat emailyang tercantum.

  • Bila tidak ada tanggal dan waktu atau yang tercantum sudah kadaluarsa didalam artikel mohon tanyakan kepada kami untuk jadwal terbarunya.

  • Peserta bisa mengajukan Tanggal Pelatihan / Training selain yang tertera pada silabus penawaran.

Advertisements